Quick answer: Cracks, spalls and pits must be repaired before any floor coating, and heavy spall repair, resurfacing or removing an old coating adds to the price. Diamond grinding opens the surface so fillers and the coating bond properly.
Common Floor Problems in Local Garages
- Salt pitting and spalling: years of salty winter slush break down the surface, especially near the garage door and where cars park
- Cracks: shrinkage and settlement cracks are common. Most can be filled before coating
- Old paint or DIY coatings: peeling patches must be removed, not coated over
- Oil stains: deep oil contamination may need extra cleaning or grinding to get a good bond
- Uneven or sunken slabs: these may need concrete work beyond what a coating installer handles
What Grinding Does
Diamond grinding removes the weak top layer of concrete along with sealers, stains and old coatings. It opens the surface so the coating can soak in and grip. It's the main difference between a professional install and a kit, and it's dusty work, so ask how dust is controlled (vacuum-attached grinders are the norm).
Repairs Before Coating
Cracks are typically chased out and filled with a repair compound. Pitted and spalled areas are patched or skim-coated to bring the surface back to level. Control joints can be filled or honored, depending on the look you want.
Structural problems, like major settlement or heaving, are a job for a concrete or foundation contractor.
Common Concrete Floor Problems
Scaling and pitting
Flaking of the top surface, often near garage doors where salt brine collects. NRMCA's guidance explains that freeze-thaw cycles in saturated concrete, made worse by deicers, cause scaling.
Cracks
Shrinkage cracks are normal in concrete. Wider or moving cracks may signal settlement or heaving.
Spalls
Chunks broken out of the surface, often at joints and edges.
Settlement and low spots
Areas that sink or hold water, often from poorly compacted fill.
Repair Before Coating
Coatings bond to sound concrete. Before coating, cracks are routed and filled, spalls and pits patched, and low spots leveled. The International Concrete Repair Institute's surface preparation guidelines describe the surface profiles needed for good bonding. Skipping repairs leads to visible defects and early failures.
Static vs. Moving Cracks
Static cracks (not moving) can be filled with rigid repair materials and coated over. Moving cracks will reflect through rigid coatings; they may need flexible fillers or treatment as joints. If a slab is heaving or sections are moving, find the cause (drainage, frost, settlement) before repairing.
Salt Damage Near the Garage Door
The first few feet inside the garage door take the most abuse in Hudson Valley winters. Slush drips off cars, brine pools and freezes. Repairs here use patching materials suited to freeze-thaw exposure, followed by a coating that keeps brine out.
When Replacement Makes More Sense
Slabs broken into many moving pieces, severely heaved or deteriorated through their depth may be better replaced. An honest assessment saves money.
Moisture
Before coating repaired slabs, moisture testing (ASTM D4263 or F2170) helps avoid blistering.
Costs
Repair costs depend on the extent of damage. Crack filling and minor patching are often included in coating estimates; extensive repair or leveling adds cost. Ask for repairs to be itemized.
Preventing Damage
- Squeegee out slush and brine in winter
- Keep gutters and grading directing water away from the slab
- Coat the floor to keep brine from soaking in
- Avoid deicers with ammonium nitrate or ammonium sulfate on concrete; NRMCA notes they're especially aggressive
Repair Materials
Different repairs call for different materials. Thin cracks are often filled with epoxy or polyurea crack fillers. Pits and spalls are patched with polymer-modified repair mortars or fast-setting polyurea patching compounds. Low spots may be leveled with self-leveling underlayment where a coating will go on top. Each material has limits on thickness, temperature and compatibility with the coating; a good installer matches them.
Joints
Control joints are intentional cuts that let the slab crack in a straight line. In garages, installers often fill joints and coat over them for a seamless look; others honor joints by keeping them open. In commercial spaces with forklifts, joints are usually filled with semi-rigid fillers to protect edges.
Heaving and Frost
In the Hudson Valley, frost can lift slabs where water collects under them. Garage aprons and slabs near downspouts are common trouble spots. Fixing drainage (gutters, downspout extensions, grading) is part of a lasting repair. If a slab moves seasonally, a rigid coating will crack over the moving area.
Garage Aprons and Driveways
The exterior apron in front of the garage takes more salt and freeze-thaw than the interior. Interior coatings aren't designed for exterior exposure; exterior concrete is better protected with breathable penetrating sealers, per common industry practice. Ask about aprons separately.
DIY or Pro?
Small hairline cracks can be filled by homeowners with store-bought fillers, but repairs under a coating need to be compatible and ground flush. For anything larger, or before a professional coating, leave repairs to the installer so the repairs and the coating are covered together.
How Repairs Are Done Before a Coating
- Inspection: map cracks, spalls, low spots and joints; check for movement and moisture
- Grinding: open the surface and expose weak concrete
- Crack routing: widen cracks slightly so filler penetrates and bonds
- Filling and patching: fill cracks and patch spalls and pits with compatible material
- Grinding flush: level repairs with the surrounding slab
- Coating: apply the chosen system over the repaired surface
Done this way, repairs disappear under the coating, especially with a flake system.
Signs a Slab Needs Professional Assessment
- Cracks wider than about a quarter inch, or one side higher than the other
- Cracks that grow or change seasonally
- Sections that rock or sound hollow when tapped
- Water pooling in low spots or coming up through cracks
- Large areas of scaling or exposed aggregate
These can indicate settlement, frost heave, moisture problems or deterioration that need more than cosmetic repair.
Repair Costs in Context
Coating estimates often include routine crack filling and minor patching. Heavy pitting near the garage door, wide cracks, leveling and spall repair are usually priced separately. Ask the installer to walk the slab with you and itemize repairs so you can compare quotes on equal terms. Preparation and repair can move the final price a lot.
Repairs Without Coating
Some homeowners just want cracks and spalls fixed. That's possible, but bare repaired concrete will continue to absorb salt brine and can scale again. If you're repairing anyway, a coating protects the repairs and the rest of the slab.
For most Hudson Valley garages, the right order is simple: fix drainage, repair the slab, test for moisture, then coat. Skipping a step is the most common reason floors fail early.
Following that order keeps repairs from failing and keeps the coating bonded and looking good for the long term.
Sources
- NRMCA, Concrete in Practice CIP 2: Scaling Concrete Surfaces (deicers and freeze-thaw)
- International Concrete Repair Institute, Guideline 310.2R: Concrete Surface Preparation (CSP profiles)
- ASTM D4263, Indicating Moisture in Concrete by the Plastic Sheet Method
- ASTM F2170, Relative Humidity in Concrete Floor Slabs Using in situ Probes
- Angi, How Much Does Epoxy Flooring Cost? (2026)
Questions
Will cracks come back through the coating?
Moving cracks can telegraph through any coating over time. Static cracks that are properly filled usually stay hidden. Your installer can tell you which is which.
How long should new concrete cure before coating?
A common guideline is about 28 days for new concrete, but moisture, not just age, is what matters. Your installer will test before coating.
Can pitted concrete be coated?
Yes, after patching the pits so the surface is sound and even.
Will cracks come back through the coating?
Static cracks properly filled usually don't. Moving cracks can, unless treated as joints.
What causes scaling near my garage door?
Freeze-thaw cycles in concrete saturated with salt brine. NRMCA guidance describes the mechanism.
Should I replace or repair my slab?
Most slabs can be repaired. Severely broken, heaved or deteriorated slabs may need replacement.
Which deicers are worst for concrete?
NRMCA notes ammonium nitrate and ammonium sulfate deicers are especially damaging. Avoid applying deicers directly to garage concrete.
How long do concrete repairs take?
Most repairs are done the same day as the coating with fast-setting materials. Extensive leveling or deep patches may add a day.
Can you fix my garage apron?
Aprons are exterior concrete and need different treatment. Ask about repair and breathable sealers separately.
Why does my garage floor flake near the door?
That's scaling. Salt brine from cars soaks into the surface and repeated freezing breaks the top layer apart. Patch and coat to stop it.
Can you level a sunken section of slab?
Small low spots can be leveled with patching or self-leveling materials before coating. Large sunken sections may need lifting or replacement.
Related Services
Garage Floor Coatings
Full-broadcast flake systems over ground concrete. Slip-resistant, easy to clean, built for salt and slush.
Learn more →Epoxy Floor Coatings
Durable, economical epoxy systems for garages, basements, workshops and light commercial space.
Learn more →Polyaspartic Floor Coatings
Fast-curing, UV-stable coatings, often used as one-day garage systems or as a top coat over epoxy.
Learn more →Basement Floor Coatings
Coatings for basement slabs, with moisture testing first, for finished basements, laundry rooms and utility spaces.
Learn more →Commercial & Shop Floors
Coatings for auto shops, warehouses, retail, restaurants, offices and showrooms, scheduled around your hours.
Learn more →Get Your Floor Evaluated
Call or send the form with your town and what's happening.
- Tell us your town and the space: garage, basement or commercial
- Mention cracks, pitting, old paint or coatings, or moisture
- A local installer calls back to confirm availability and a exact pricing
Request a Floor Coating Estimate
Where This Service Is Available
Monroe, NY 10950, Chester, Goshen, Warwick, Woodbury, Central Valley & Harriman, Middletown, Newburgh, New City, Pomona, Suffern, Nanuet, plus Harriman, Highland Mills, Washingtonville, Blooming Grove, Florida, Pine Bush, Montgomery, Walden and nearby communities. All service areas.