Quick answer: Sweep or dust-mop often to remove grit, mop with a diluted pH-neutral cleaner, and wipe up spills promptly. Avoid ammonia, bleach, vinegar, and strong acidic or alkaline cleaners, as well as steel wool, aggressive pads and wire brushes. Use walk-off mats and felt pads, and lift heavy items instead of dragging them. In winter, rinse road salt and slush off regularly. Textured, slip-resistant floors need a stiff-bristled broom or deck brush. Depending on traffic, HTS says polyaspartic floors may need a recoat every 3 to 5 years, after cleaning and mechanical abrasion.
One reason people coat a garage floor is that bare concrete is hard to keep clean: it soaks up oil, dust and salt. A good epoxy or polyaspartic coating seals the surface, so most dirt stays on top where you can sweep or mop it away. But coatings have limits. The wrong cleaner can dull or stain the finish, and grit acts like sandpaper under tires and boots. This guide pulls together what coating makers recommend, so your floor keeps its look.
Routine cleaning
HTS Chemical's maintenance guide for its polyaspartic topcoats lists the basics:
- Sweep or dust-mop regularly with a microfiber dust mop to remove grit and debris.
- Spot-clean spills right away with a damp mop or cloth.
- Use a neutral pH cleaner diluted in water.
- Damp-mop periodically with the diluted cleaner, avoiding excess water or puddles.
SUNDEK's guide for high-performance floor coatings agrees: clean promptly, because it makes dirt, grease and other contaminants easier to remove and helps prevent staining by some strong chemicals. It recommends mild, non-caustic cleaners that rinse freely, or a non-filming detergent, and says to avoid abrasive cleaners that may dull the surface.
What not to use
HTS's list of things to avoid:
- Ammonia, bleach, vinegar, or alkaline or acidic cleaners
- Steel wool, aggressive scrubbing pads or wire-bristle brooms
- Liquids left standing on the surface
- Prolonged exposure to strong acids, solvents or corrosives
- Prolonged exposure to extreme heat
SUNDEK adds that aggressive, caustic cleaners can stain the finish, and that aggressive abrasion from cleaning machines can dull a glossy coating over time. As it puts it, two-component coatings are scratch resistant, but no floor coating is scratch proof.
For stubborn spots, SUNDEK says a mild solvent such as paint thinner may be used for spot cleaning on its epoxy, polyurethane and polyaspartic finishes, applied with a damp cloth rather than poured on the floor and rinsed off immediately. Test anything new in a corner first and check with your installer for your specific product.
Winter: salt, slush and sand
Hudson Valley winters bring road salt, brine and sand into the garage on every car. Salt water left to dry leaves a white film, and sand under tires is abrasive. Based on the guidance above:
- Squeegee meltwater toward the door or drain rather than letting it pool. HTS warns against leaving standing liquid.
- Sweep up sand and grit often, since that is what wears the finish.
- Rinse and mop with a pH-neutral cleaner after storms, when the floor dries out enough to work on.
- Use mats or a containment mat where the car drips most. HTS recommends walk-off mats at entrances.
See also garage floor coatings and Hudson Valley winters.
Pressure washing
SUNDEK says its epoxy, polyurethane and polyaspartic finishes on exterior floors may be washed with a 2000 to 2500 psi pressure washer, and that pressure washing with hot water is not recommended. That guidance is written for exterior floors, so for a garage, ask your installer before pressure washing, keep the nozzle moving, and don't aim at edges or chips where water could get under the coating.
Floor looking dull or worn?
Call (845) 653-3873 or use the estimate form below. Tell us your town, the garage size and what the floor looks like now.
Protect the surface
- Felt pads. Both HTS and SUNDEK recommend felt pads under furniture and movable objects.
- Lift, don't drag. SUNDEK says to lift furniture rather than drag it. HTS says not to drag equipment, pallets or sharp objects across the surface.
- Rolling chairs. SUNDEK recommends chair mats under chairs with wheels. A rolling stool or creeper in a garage workshop is similar.
- Jack stands and kickstands. Put a plywood square or a puck under them to spread the point load.
Cleaning textured, slip-resistant floors
If your floor has a texture additive or a heavy flake broadcast, SUNDEK notes that the more textured the surface, the harder it is to get dirt out. It says slip-resistant floors must be cleaned with a stiff-bristled broom or a floor machine with a medium brush, and that a deck brush works well for small areas. See slip-resistant garage floor coatings.
Inspect, touch up and recoat
HTS recommends regular inspections for wear or damage, especially in high-traffic areas. Minor scratches or worn areas may be repaired with compatible polyaspartic material after proper surface prep. Depending on traffic and exposure, HTS says floors may need recoating every 3 to 5 years, and that surfaces must be thoroughly cleaned and mechanically abraded before recoating so the new coat bonds. SUNDEK also says periodic recoating will completely renew the surface, done in strict accordance with the manufacturer's instructions.
If a section is lifting or flaking, that's different from normal wear. See why garage floor coatings peel.
New floor? Wait out the cure
During the initial cure, HTS says to avoid heavy traffic, equipment and furniture, keep the floor dry and free of debris, and not clean it with water or chemicals. See garage floor coating cure time.
Related: polyaspartic floor coating, epoxy floor coating and garage floor coating cost.
Sources
- HTS Chemical, Polyaspartic Topcoat Maintenance Guide (PAS-100 / PAS-200, PDF)
- SUNDEK, Maintenance for High Performance Floor Coatings Guide (PDF)
Questions
What is the best cleaner for an epoxy or polyaspartic garage floor?
A neutral pH cleaner diluted in water, or a mild non-filming detergent. Avoid ammonia, bleach, vinegar and strong acidic or alkaline cleaners.
Can I use bleach on my coated garage floor?
HTS's maintenance guide says to avoid bleach, ammonia, vinegar and other alkaline or acidic cleaners.
Can I pressure wash a coated garage floor?
SUNDEK allows 2000 to 2500 psi with cold water on exterior coated floors. Ask your installer first for a garage floor, keep the nozzle moving and avoid edges and chips.
How do I get road salt off my garage floor coating?
Squeegee meltwater out, sweep up sand, and mop with a diluted pH-neutral cleaner. Don't let salty water stand.
How often does a garage floor coating need to be recoated?
HTS says polyaspartic floors may need recoating every 3 to 5 years depending on traffic and exposure, after cleaning and mechanical abrasion.
More Guides
- Epoxy vs. polyaspartic garage floors
- Garage floor coating cost in Orange & Rockland
- Garage floors & Hudson Valley winters
- How to prepare your garage for coating
- Coating vs. interlocking tiles and mats
- Concrete sealer vs. floor coating
- How long a garage floor coating takes to cure
- Why garage floor coatings peel
- Slip-resistant garage floor coatings
Want a Pro to Take a Look?
Call or send the form with your town and what you're seeing.
- Tell us your town and the space: garage, basement or commercial
- Mention cracks, pitting, old paint or coatings, or moisture
- A local installer calls back to confirm availability and a exact pricing