Quick answer: Smooth epoxy and polyaspartic coatings can be slippery when wet. The coating makers SUNDEK and HTS both say so. Grip comes from texture. A full flake broadcast gives some, and an aluminum oxide additive gives more. It is either broadcast into the coat or mixed into the topcoat. Torginol's data sheet gives about 1 lb per 5 to 10 sq ft for coarse 50-mesh grit, or 2 to 4 lb per gallon mixed in for the finer grades. More texture means more grip but harder cleaning. For a home garage that sees winter slush, a medium texture is a reasonable middle ground. Businesses must also meet OSHA's walking-surface rules.
Garages in the Hudson Valley get wet: rain off the car, snow melting off the wheel wells, salty slush tracked in from the driveway. A high-gloss smooth coating is easy to clean, but it is not where you want to be walking in socks or work boots when there's water on it. The good news is that slip resistance is a choice you make during installation, not a separate product. Here's how it works.
Why smooth coatings get slippery
SUNDEK's maintenance guide for high-performance floor coatings is direct: a smooth floor coating finish will be slippery when wet, but very easy to keep clean. HTS Chemical's polyaspartic maintenance guide says the same: when installed without added texture, its coatings can be slippery when wet, and it recommends a non-slip additive, floor mats or coatings in areas prone to wet conditions. Water, oil, antifreeze and salt brine all make a smooth surface slicker.
Ways to add texture
Decorative flake broadcast
Many garage systems have vinyl flakes broadcast into the base coat and locked in with a clear topcoat. The flakes add some texture, especially with a thinner topcoat over them. With a heavy topcoat, the surface can end up fairly smooth again. Ask how the topcoat will be applied if grip matters to you.
Aluminum oxide additive
Aluminum oxide is a hard grit used as an anti-slip texture in floor coatings. Torginol's product data sheet describes it as a dense white material that dries clear and can be either hand-broadcast or mixed into a floor coating. The sheet lists a Mohs hardness of 9 and compatibility with epoxy, polyaspartic, polyurethane, polyurea and other resin systems. It recommends:
- Coarse (50 mesh): hand-broadcast at about 1 lb per 5 to 10 sq ft.
- Fine (100 or 200 mesh): mixed directly into the coating at 2 to 4 lb per gallon.
Coarser grit gives more bite but feels rougher under bare feet and holds more dirt. Finer grit mixed into the topcoat gives a subtler texture. Your installer picks the grade and rate for the product and how you use the space.
Other options
Quartz broadcast systems, used in some commercial floors, also give a textured surface. Mats at the door and where the car drips add grip where water lands. HTS lists floor mats as one of its options for wet areas.
The tradeoff: grip vs. cleaning
SUNDEK says a moderate or aggressive texture offers safety against slips and falls but may require changing how you clean. The more textured the surface, the harder it is to reach and remove dirt. It says slip-resistant floors must be cleaned with a stiff-bristled broom or a floor machine with a medium brush, rather than just a mop. See how to clean and maintain a coated garage floor.
Want a floor that's easier on your feet in winter?
Call (845) 653-3873 or use the estimate form below. Tell us your town, the garage size and how you use the space.
Choosing a texture level
| Texture | Grip when wet | Cleaning | Good for |
|---|---|---|---|
| Smooth, no additive | Low | Easiest | Showroom floors, dry storage |
| Flake with thin topcoat or fine grit | Moderate | Easy | Most home garages |
| Coarse grit broadcast | High | Needs a stiff brush | Ramps, entries, wash bays, shops |
A floor can use more than one level. You can ask for extra texture near the door, around the car's wet zone, and on steps or ramps, with less texture elsewhere. Just make sure the installer plans the transitions.
Commercial and shop floors
If the space is a workplace, OSHA's general walking-working surface rule, 29 CFR 1910.22, requires employers to keep floors clean and, as far as feasible, dry, and to keep walking-working surfaces free of hazards such as spills, snow and ice. Where wet processes are used, drainage must be maintained and, to the extent feasible, dry standing places such as platforms or mats provided. Surfaces must be inspected regularly and maintained in a safe condition. A coating alone doesn't make a floor compliant, but texture is one tool. See commercial floor coating.
Can texture be added later?
Often, yes, as part of a recoat. HTS says surfaces must be thoroughly cleaned and mechanically abraded before recoating so the new coat bonds. A textured topcoat can then go over the existing system. See why garage floor coatings peel for why prep matters.
Related: epoxy vs. polyaspartic, coatings and Hudson Valley winters and garage floor coating.
Sources
- SUNDEK, Maintenance for High Performance Floor Coatings Guide (PDF)
- HTS Chemical, Polyaspartic Topcoat Maintenance Guide (PAS-100 / PAS-200, PDF)
- Torginol, Aluminum Oxide Texture Additive Product Data Sheet (PDF)
- OSHA, 29 CFR 1910.22 Walking-Working Surfaces: General Requirements
Questions
Are epoxy garage floors slippery?
A smooth finish can be slippery when wet. Coating makers SUNDEK and HTS both say so. Texture, from flakes or an aluminum oxide additive, adds grip.
What is added to floor coatings to make them non-slip?
Usually aluminum oxide grit, broadcast into the coat or mixed into the topcoat. Quartz and flake broadcasts also add texture.
Does a non-slip additive make the floor harder to clean?
Yes, somewhat. SUNDEK says textured floors should be cleaned with a stiff-bristled broom or a floor machine with a medium brush.
Can I add slip resistance to an existing coated floor?
Usually during a recoat, after the floor is cleaned and mechanically abraded so a textured topcoat bonds.
Do businesses need slip-resistant floors?
OSHA 1910.22 requires employers to keep walking-working surfaces clean, dry where feasible, and free of hazards such as spills, snow and ice. Texture is one way to help.
More Guides
- Epoxy vs. polyaspartic garage floors
- Garage floor coating cost in Orange & Rockland
- Garage floors & Hudson Valley winters
- How to prepare your garage for coating
- Coating vs. interlocking tiles and mats
- Concrete sealer vs. floor coating
- How long a garage floor coating takes to cure
- Why garage floor coatings peel
- How to clean and maintain a coated garage floor
Want a Pro to Take a Look?
Call or send the form with your town and what you're seeing.
- Tell us your town and the space: garage, basement or commercial
- Mention cracks, pitting, old paint or coatings, or moisture
- A local installer calls back to confirm availability and a exact pricing